高G弹丸引信遥测装置的设计与研制

介绍一种小型的能够承受膛内发射或解爆抛撒高冲击过载的无线遥测装置。这套独立的遥测弹载设备安装在体积很小的引信腔内 ,不需要对弹丸进行改装。这种新型遥测装置能够完成膛内或解爆抛撒及飞行过程中作用在引信上的单轴向或三轴向的加速度和振动测量 ,是引信故障分析和改进设计的重要手段。     

混杂难熔金属C/C复合材料中金属与碳反应初步研究

研究了碳纤维难熔金属纤维混杂增强碳基体复合材料中难熔金属与碳之间的化学反应.结果表明,条件不同,难熔金属W丝、Ta丝与不同形式碳的反应程度、反应产物及结构有很大的区别.低温区,难熔金属与碳不发生明显化学反应,中温区W丝可与气态的碳氢气体发生轻微化学反应,高温区W丝、Ta丝可与固态沥青碳以及碳纤维发生反应.通过控制反应条件,可以得到难熔金属纤维碳纤维混杂增强碳基体、含难熔金属碳化物的难熔金属纤维碳纤维混杂增强碳基体和难熔金属碳化物纤维碳纤维混杂增强碳基体复合材料.     

基于可变滑动窗口与3σ准则的脉冲星信号去噪算法

针对地面接收射电观测脉冲星信号较弱、信噪比较低的问题,提出了基于可变滑动窗口与两层3σ准则的信号去噪算法。该算法引入可变滑动窗口,对信号进行分步连续处理,同时在筛选噪声时使用两层3σ准则算法,解决了噪声遗漏及过度去噪问题。为证明算法可靠性与实用性,利用佳木斯66 m观测站实测数据进行算法验证,针对J1939+2134与J1744—1134脉冲星的实测数据进行分析处理。结果表明,该算法能够对脉冲星数据进行有效去噪,普遍提高信噪比约10dB。     

钉头型式对复合材料层合板机械连接强度的影响

通过3种不同铺层比例的复合材料层合板机械连接接头的挤压强度测试，研究了钉头型式对复合材料层合板机械连接挤压力学性能的影响，获得了沉头螺栓挤压强度修正系数。试验数据表明：采用沉头螺栓的复合材料机械接头 的挤压强度，可达到采用凸头螺栓的复合材料机械连接挤压强度的90%左右，但接头刚度仅为采用凸头螺栓的复合材料接头刚度的40%~50%。研究采用Hashin失效准则和Tan-Camanho损伤扩展方法，对两种钉头型式的复合材料层合板机械连接接头的挤压失效过程进行了有限元分 析，预测了复合材料层合板机械连接接头的偏移挤压强度和极限挤压强度，模型预测值与试验值的误差不超过15%。     

Optimal network topology of relative navigation and communication for navigation sharing in fractionated spacecraft cluster

Navigation sharing as a key technology provides orbit and attitude information broadcasting for the whole fractionated spacecraft cluster (FSC). The navigation sharing concept has already been proposed for some years. However, the problem of achieving the optimal navigation sharing by designing the proper network topology is still unsolved, especially in the case that some members of the cluster have absolute navigation devices, some just have relative navigation devices and some only have communication devices. In this paper, a comprehensive model of describing the navigation sharing problem in FSC is proposed. The model of network topology constructing by relative navigation links and communication links is established. By using the graph theory and genetic algorithm as the tool, the conditions for navigation sharing in FSC with different sharing degrees are obtained. Finally, some examples are presented to test the methods, and it has been found that, the absolute positions and attitudes of all the members can still be determined even some members in FSC have no absolute navigation devices.     

模型燃烧室油雾特性试验

利用粒子图像测速仪(Particle imaging velocimetry,PIV)测量斜切径向旋流器模型燃烧室内油雾特性,试验研究不同进气温度、流量和油气比对燃烧室内油珠颗粒大小及其分布的影响.试验结果表明:模型燃烧室内不同区域的油珠数密度明显不同,但油珠粒径分布基本相同;进气温度升高和油气比增大,使得燃烧室中油雾的索太尔平均直径(Sauter mean diameter,SMD)减小,燃油雾化得到改善;而进气流量的变化对燃烧室中油雾的SMD影响不大.     

防空雷达精确预警关键技术研究

精确化防空是未来防空作战的发展趋势,而精确预警是精确防空作战的前提和基础。针对防空雷达精确预警存在的不足,研究了基于“北斗一号”卫星定位系统的精确标定和时间校准的方法,探讨了提高防空雷达预警探测精度的方法,在空间校准、时间统一的基础上研究了雷达组网的数据融合问题。     

Optimization of communication network topology for navigation sharing among distributed satellites

Navigation sharing among distributed satellites is quite important for coordinated motion and collision avoidance. This paper proposes optimization methods of the communication network topology to achieve navigation sharing. The whole communication network constructing by inter-satellite links are considered as a topology graph. The aim of this paper is to find the communication network topology with minimum communication connections’ number (MCCN) in different conditions. It has found that the communication capacity and the number of channels are two key parameters affecting the results. The model of MCCN topology for navigation sharing is established and corresponding method is designed. Two main scenarios, viz., homogeneous case and heterogeneous case, are considered. For the homogeneous case where each member has the same communication capacity, it designs a construction method (Algorithm 1) to find the MCCN topology. For the heterogeneous case, it introduces a modified genetic algorithm (Algorithm 2) to find the MCCN topology. When considering the fact that the number of channels is limited, the Algorithm 2 is further modified by adding a penalized term in the fitness function. The effectiveness of these algorithms is all proved in theoretical. Three examples are further tested to illustrate the methods developed in this paper.     

基于相关分析和组合神经网络的退化预测

产品剩余寿命预测是加速退化试验和故障预测与健康管理两大热点领域中的关键技术之一.为了解决复杂退化的预测问题,提出了一种新型预测方法,对退化轨迹能够实现较长距离的预测.此方法首先对复杂退化数据进行小波变换,通过Durbin-Watson方法和偏相关图分析各级分解序列的自相关性,最后根据序列的特点,组合BP(Back Propagation)和小波神经网络对退化轨迹进行预测.为了验证所提组合神经网络方法的有效性,采用小波神经网络的预测结果进行对比分析.实际退化数据的预测结果表明,所提方法比单独采用小波神经网络,具有更小的均方差(MSE,Mean Square Error),对剩余寿命(RUL,Remaining Useful Life)也具有更高的预测精度.     

高温处理对中密度针刺C/C复合材料性能的影响

针对C/C复合材料脆性问题,对密度为1.60 g/cm3的碳布叠层针刺C/C复合材料进行了1800、2 000、2 200和2 500℃的高温处理,研究了不同热处理温度对C/C复合材料微晶结构、力学和抗热震等性能的影响.结果表明,高温处理使针刺C/C复合材料的层间剪切和面内拉伸强度出现不同程度的降低,但材料的断裂伸长率和抗热震性能得到大幅度提高.其中,1 800℃高温处理后的C/C复合材料具有优异的力学和抗热震性能.